200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 201-210

By on April 22, 2015
Ensurepass="cursor: auto; margin: 0cm 0cm 0pt; text-justify: inter-ideograph; line-height: normal" align="justify">  QUESTION 201 Which three statements about VTP features are true? (Choose three.)   A.       VTP works at Layer 3 of the OSI model and requires that a management VLAN IP address be configured. B.        When properly configured, VTP minimizes VLAN misconfigurations and configuration inconsistencies. C.        Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 211-220

By on
Ensurepass  QUESTION 211 Refer to the exhibit. A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What could be the cause of the problem?     A.       The serial cable on R1 needs Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 171-180

By on
Ensurepass  QUESTION 171 Which command enables IPv6 forwarding on a Cisco router?   A.       ipv6 local B.        ipv6 host C.        ipv6 unicast-routing D.       ipv6 neighbor   Correct Answer: C     QUESTION 172 When using the CLI, which banner displays a message upon every connection that is made into the router?   A.      Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 181-190

By on
Ensurepass  QUESTION 181 What is one benefit of PVST+?   A.       PVST+ supports Layer 3 load balancing without loops. B.        PVST+ reduces the CPU cycles for all the switches in the network. C.        PVST+ allows the root switch location to be optimized per VLAN. D.       PVST+ automatically selects the root bridge location, to provide optimized bandwidth Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 151-160

By on
Ensurepass  QUESTION 151 Which two states are the port states when RSTP has converged? (Choose two.)   A.      blocking B.      listening C.      learning D.      forwarding E.       disabled   Correct Answer: AD     QUESTION 152 Which two statistics appear in show frame-relay map output? (Choose two.)   A.       Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 161-170

By on
Ensurepass  QUESTION 161 Which name describes an IPv6 host-enabled tunneling technique that uses IPv4 UDP, does not require dedicated gateway tunnels, and can pass through existing IPv4 NAT gateways?   A.       manual 6to4 B.        dual stack C.        dynamic D.       Teredo   Correct Answer: D     QUESTION 162 What is the default maximum number Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 131-140

By on
Ensurepass  QUESTION 131 Refer to the exhibit. A technician is testing connection problems in the internetwork. What is the problem indicated by the output from HostA?     A.       The routing on Router2 is not functioning properly. B.        An access list is applied to an interface of Router3. C.        The Fa0/24 interface of Switch1 is down. D.       Read more [...]

Continue Reading

200-101 Real Tests (Spring 2015)

Download New Updated (Spring 2015) Cisco 200-101 Actual Tests 120-130

By on
Ensurepass="cursor: auto; margin: 0cm 0cm 0pt; text-justify: inter-ideograph; line-height: normal" align="justify">  QUESTION 121 Refer to the graphic. A company wants to use NAT in the network shown. Which commands will apply the NAT configuration to the proper interfaces? (Choose two.)   A.       R1(config)# interface serial0/1 R1(config-if)# ip nat inside   B.        R1(config)# interface serial0/1 R1(config-if)# Read more [...]

Continue Reading