Latest Certified Success Dumps Download

CISCO, MICROSOFT, COMPTIA, HP, IBM, ORACLE, VMWARE
648-247 Latest Exam (Sep 2017)

[Free] 2017(Sep) EnsurePass Passguide Cisco 648-247 Dumps with VCE and PDF 11-20

September 4, 2017

EnsurePass
2017 Sep Cisco Official New Released 648-247
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/648-247.html

Implementing Cisco Connected Physical Security 2 Exam (CCSP 2)

Question No: 11

Cisco Physical Access Control Gateways and Reader Modules are compatible with which of the following Reader Types?

  1. proximity readers only

  2. Cisco Readers only

  3. any Wiegand Compatible Reader

  4. any card reader

Answer: C

Question No: 12

Which devices does Cisco manufacture and sell?

  1. readers, locks, and door position switches

  2. locks, doors, and door hardware

  3. cards, card printers, and readers

  4. Cisco does not manufacture or sell readers, locks, door hardware, or card printers

Answer: D

Question No: 13

How are nonstandard, third-party devices (temperature sensors, water sensors, and so on) added and managed in Cisco Physical Access Manager software?

  1. These devices cannot be added to Cisco PAM.

  2. A new device template can be created and the device added to the gateway or module.

  3. Devices will only appear as quot;Generic Inputquot; or quot;Generic Outputquot;-system messages that cannot be defined for specific third-party devices.

  4. A new device template can be created and added to the gateway. The device will only appear as quot;Generic Inputquot; or quot;Generic Output.quot;

Answer: B

Question No: 14

Assume a single badge entry in Cisco PAM for each user. For a single user, which two of the following statements are true regarding Cisco PAM, proximity card readers, and keypads? (Choose two.)

  1. Keypads are not supported. Cisco PAM will work with Wiegand card readers only.

  2. Cisco PAM can be used with Wiegand proximity card readers with integrated keypads.

  3. Cisco PAM can be used with Wiegand proximity card readers only or Wiegand keypads only.

  4. Cisco PAM can be used with both Wiegand proximity card readers and Wiegand keypads.

  5. Cisco PAM can use non-Wiegand keypads.

Answer: B,C

Question No: 15

A gateway recently has been added to the network but does not appear in Cisco PAM. The gateway can be pinged from the user#39;s laptop as well as the Cisco PAM server. Which of the following might cause this issue?

  1. The gateway does not have the correct Cisco PAM Server IP address.

  2. The gateway is not on the same network segment as the access control server.

  3. The gateway has a different firmware version than the server.

  4. The gateway does not have the correct Cisco PAM Server IP address, and the gateway has a different firmware version than the server.

Answer: D

Question No: 16

A gateway is reporting unstable or flapping connectivity. INPUT 1 is rapidly flapping between quot;upquot; and quot;down.quot; What is the most likely cause?

  1. The input is configured as supervised, when it should be unsupervised.

  2. The wires are dirty or improperly seated in the termination block.

  3. The gateway is defective and should be RMA.

  4. The input on the gateway is configured as supervised, and the wires could be dirty or improperly seated in the termination block.

Answer: D

Question No: 17

How can Cisco Physical Access Control (Cisco PAC) modules directly interface with fire alarm systems for door release function?

  1. Cisco PAC modules should not directly interface with firm alarm systems for door release functions.

  2. Cisco PAC modules can directly interface with fire alarm systems for door release functions via the CAN bus.

  3. Cisco PAC modules can directly interface with fire alarm systems for door release functions via open APIs in the Cisco PAM.

  4. Cisco PAC modules cannot directly interface with fire alarm systems for door release functions because the modules are digital and fire alarm systems are analog.

Answer: A

Question No: 18

You just received a new Cisco PAM appliance from Cisco. After unpacking the new server and plugging it into the network, how does the new Cisco PAM appliance get an IP address upon being powered on for the first time?

  1. Cisco PAM will request an IP address via DHCP.

  2. Cisco PAM will first request an IP address via DHCP. If Cisco PAM does not receive a DHCP response, it will assign itself an IP address of 192.168.1.2.

  3. Cisco PAM is statically configured with an IP address of 10.1.1.2.

  4. Cisco PAM is statically configured with an IP address of 192.168.1.2.

Answer: D

Question No: 19

In Cisco PAM, how do you configure items such as DNS, system upgrades, and rebooting of the server?

  1. via a web browser and logging into the Cisco PAM Server Administration web page

  2. by using the Cisco PAM Java Client

  3. Cisco PAM is configured using Cisco VSOM

  4. by using the Cisco PAM EDI Studio application

Answer: A

Question No: 20

How many licenses are included with Cisco PAM, and how are licenses allocated?

  1. Cisco PAM does not come with any licenses. Licenses are allocated for every logical door.

  2. Cisco PAM comes with 1 license. It is allocated for the admin user.

  3. Cisco PAM comes with 32 licenses. Each module requires 1 license.

  4. Cisco PAM comes with 64 licenses. Only gateways require licenses.

Answer: C

100% Free Download!
Download Free Demo:648-247 Demo PDF
100% Pass Guaranteed!
Download 2017 EnsurePass 648-247 Full Exam PDF and VCE

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 EnsurePass IT Certification PDF and VCE