642-035 Latest Exam (Aug 2018)

[Free] 2018(Aug) Dumps4cert Cisco 642-035 Dumps with VCE and PDF Download 11-20

August 7, 2018

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Aug Cisco Official New Released 642-035
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco Unified Computing

Question No: 11

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

Which mistake did the UCS administrator make when trying to access the GUI?

  1. specified the incorrect login domain

  2. did not use the VIP

  3. tried to login before the GUI had fully booted up

  4. password is incorrect

  5. attempted to login to the subordinate cluster peer

Answer: E

Question No: 12

During a Cisco UCS firmware update via the UCS Manager GUI, you choose All from the Filter list in the Activate Firmware dialog box. Which statement about this action is true?

  1. Because many releases and patches have dependencies that require a specific order, this method is not preferred, and you should consult the release notes.

  2. This setting will work and UCS Manager will properly activate all elements in the correct order.

  3. This setting will have no effect, and you should always use the CLI to complete firmware upgrades.

  4. You should open a case with Cisco TAC to determine what to do.

Answer: A

Question No: 13

What should you do when you see faults during the initial setup and discovery process?

  1. Take note and address the faults.

  2. You can safely ignore these faults.

  3. Log them and try to address the first one.

  4. Reboot until the error messages go away.

Answer: B

Question No: 14

When using the Cisco UCS Manager GUI to troubleshoot a suspected bad memory, which logs contain data that are related to the faulty DIMM?

  1. the System Event log and Faults log that are located under the Admin tab

  2. the Events log and Faults log that are located under the Admin tab

  3. the System Event log that is located under the Server tab in the Navigation panel and the Faults log that is located under the Admin tab

  4. the System Event log that is located under the Equipment tab and the Faults log that is located under the Admin tab

Answer: D

Question No: 15

At any given time, each server can be associated with how many service profiles?

  1. 1

  2. 2

  3. 5

  4. 10

  5. unlimited

Answer: A

Question No: 16

Which command must you use to find information about system event logs?

  1. UCS-TEST-DMZ-A/security #show audit-logs

  2. UCS-TEST-DMZ-A/cimc/log#show entries

  3. UCS-TEST-DMZ-A/system/control-ep#show communication-policy-ctrl

  4. UCS-TEST-DMZ-A#/org/service-profile#show pending-changes detail

Answer: B

Question No: 17

Refer to the exhibit. A system administrator reviews the VIF paths and discovers an error. What is the cause of the error?

Dumps4Cert 2018 PDF and VCE

  1. The server has no connection to the SAN.

  2. The server is still booting over SAN.

  3. The server is still booting over iSCSI.

  4. The server has the VIC with errors and needed to make an RMA.

  5. The switch that is connected the fabric interconnect has a port that is unavailable.

Answer: C

Question No: 18

After you hot swap an HDD, the updated HDD metrics fail to appear in the Cisco UCS Manager GUI. Which option is the most likely cause of the problem?

  1. The Cisco UCS Manager gathers hard disk metrics only during a system boot.

  2. The hard disk firmware version is unsupported.

  3. The hard disk failed to initialize.

  4. The hard disk is a member of a RAID-1 array.

Answer: A

Question No: 19

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

Which interface is configured as a management interface for the Cisco UCS chassis?

  1. eth0

  2. vlan4047

  3. eth1

  4. eth2

Answer: A

Question No: 20

A customer is configuring SAN pin groups in a Cisco UCS domain. The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Which of these must be done for pinning to work correctly?

  1. Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile that is assigned to that server.

  2. Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.

  3. The customer must have Cisco UCS Manager version 2.0 or above.

  4. Fibre Channel switch mode needs to be configured first.

Answer: A

100% Dumps4cert Free Download!
642-035 PDF
100% Dumps4cert Pass Guaranteed!
642-035 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No