642-035 Latest Exam (Aug 2018)

[Free] 2018(Aug) Dumps4cert Cisco 642-035 Dumps with VCE and PDF Download 31-40

August 7, 2018

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Aug Cisco Official New Released 642-035
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco Unified Computing

Question No: 31

Which three components are updated using the Host Upgrade Utility? (Choose three.)

  1. BIOS

  2. Network Adapter(s)

  3. Array Controller

  4. Cisco IMC

  5. LOM port

  6. UCSM

  7. Drive Firmware

Answer: A,B,D

Question No: 32

A customer is configuring an upstream disjoint Layer 2 network in a Cisco UCS domain. So far they have configured the following:

Fabric Interconnects are in switching mode.

There is symmetrical configuration for high availability. There are no overlapping VLANs.

Each vNIC is communicating with one disjoint Layer 2 network.

After validating the above, the customer is still having issues with network connectivity. What is the issue?

  1. Overlapping VLANs are allowed in a disjoint Layer 2 network.

  2. The vNIC configuration is incorrect and must communicate with two or more disjoint layer 2 networks.

  3. The fabric interconnect must be in end-host mode for a disjoint Layer 2 network.

  4. Asymmetrical configuration for high availability needs to be configured.

Answer: C

Question No: 33

A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure?

  1. The local disk must be the first device in the boot order.

  2. eUSB is not a supported boot device.

  3. eUSB support is available only on the Cisco UCS C-Series rack server.

  4. eUSB is not the first device in the boot order for the server.

Answer: D

Question No: 34

A UCS Admin is trying to launch the KVM console but it is failing to launch. All IP Pools for mgmt are configured and the CIMC has an address in UCSM. They SSH to the fabric Interconnect and run an ethanalyzer while issuing a ping from their local PC to the KVM IP address. The ping is successful but they do not see the ICMP requests and replies displayed in the capture. Here is the filter they used:

FIA(nxos)# ethanalyzer local interface mgmt display-filter icmp limit-captured-frames 0

What could be the reason pings are not seen in the capture and the KVM is failing to load?

  1. Java settings are preventing the KVM from loading

  2. There is a duplicate IP address for that CIMC address

  3. The switch upstream from the FI has the wrong vlan configured

  4. The CIMC IP pool is in the same subnet as the Fabric Interconnects mgmt 0 interface

Answer: B

Question No: 35

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Dumps4Cert 2018 PDF and VCE

Which two virtual Fibre Channel interfaces are able to pass trafficVSAN 11? {Choose two.)

  1. 11

  2. 12

  3. 13

  4. 14

  5. 15

  6. 10

Answer: A,B

Question No: 36

You successfully install VMware ESXi 5.0 U1 on a Cisco UCS B200 M3 server to a Fibre Channel LUN. When you reboot the server, you see the message quot;Reboot and Select Proper Boot device or insert Boot Media in selected Boot device and press a key.quot; What are the first two pieces of information you should gather to troubleshoot the boot failure? (Choose two.)

  1. Connect to the NX-OS shell via the CLI and run the show npv flogi-table command.

  2. SSH to the MDS 9124 and run the show flogi database command.

  3. Validate the boot target WWPN and LUN ID in the service profile.

  4. Validate the correct source WWPN in the service profile vHBA definition.

  5. Validate zoning for your WWPN on the Cisco MDS 9124.

  6. Validate that the boot order indicates the vHBA as the first device.

  7. Ensure LUN masking is correctly configured on the storage controller.

Answer: C,F

Question No: 37

What task is required before adding traffic sources to a monitoring session?

  1. create a traffic monitoring session

  2. choose a source component

  3. activate the session

  4. delete any earlier data collection

Answer: A

Question No: 38

The Cisco UCS Manager displays FSM information for which four of these? (Choose four.)

  1. which FSM task is being executed

  2. the current state of an FSM task

  3. the status of the previous FSM task

  4. any error codes returned while processing

  5. all completed FSM tasks

  6. multiple FSM tasks that completed over multiple tries

  7. multiple FSM tasks that failed

Answer: A,B,C,D

Question No: 39

Dumps4Cert 2018 PDF and VCE

Which of these is a supported Cisco C-Series integration topology? A)


Dumps4Cert 2018 PDF and VCE


Dumps4Cert 2018 PDF and VCE


Dumps4Cert 2018 PDF and VCE

  1. Exhibit A

  2. Exhibit B

  3. Exhibit C

  4. Exhibit D

Answer: B

Question No: 40

During a password recovery of a Cisco UCS system in a cluster configuration, what happens to blade traffic?

  1. There is no interruption to traffic, as the fabrics go down one at a time.

  2. Traffic stops flowing until the process is complete.

  3. There is no interruption to traffic because both fabrics stay up the whole time.

  4. Traffic will continue to flow, but at a limited rate until the process is complete.

Answer: B

100% Dumps4cert Free Download!
642-035 PDF
100% Dumps4cert Pass Guaranteed!
642-035 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No