300-370 Latest Exam (Aug 2018)

[Free] 2018(Aug) Ensurepass Cisco 300-370 Dumps with VCE and PDF 11-20

August 4, 2018

Ensurepass.com : Ensure you pass the IT Exams
2018 Aug Cisco Official New Released 300-370
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco Wireless Enterprise Networks

Question No: 11

Two 5508 Wireless Lan Controllers are managing all Access Points throughout the network The WLCs are located in different locations to provide geographical redundancy A Mobility Group has been configured on both WLCs and has a UP status on both Controllers The

APs m location A are statically configured to use Controller A as the Primary and Controller B as the Secondary If the WLC in location A goes offline, the APs successfully join the WLC m location B but they do not failover to their Primary configured Controller What configuration task will fix this issue#39;

  1. Change the AP Failover Priority to critical.

  2. Enable AP Fallback globally on the WLC.

  3. Configure the WLC in location A as Primary using the CAPWAP AP Controller IP Address command on all the location A Access Points.

  4. Use DHCP Option 43 and specify WLC in location A as Primary.

Answer: C

Question No: 12

Which statement describes how the Hand Select feature works on the wireless controller? Refer to the exhibit.

Ensurepass 2018 PDF and VCE

  1. The access point uses the load balancing feature to move the clients to 5 Ghz.

  2. The access point changes the DTIM period on the 2 4 Ghz band.

  3. The access point recommends the band in the association response to the client.

  4. The access point ignores and delays the probe request of the client on the 2 4 Ghz.

Answer: C

Question No: 13

A Wireless LAN Cisco engineer is troubleshooting 802. 11ac WLAN at customer site Doe to interferences with neighboring 802 11n networks the engineer must determine the current primary secondary channel allocation to enhance the current configuration.

Channel 60 has been chosen by the customer as primary 20 MHz channel. Which combination determines the resulting primary 40 MHz and primary 80 MHZ channels?

  1. primary 40 MHz channel 62, primary 80 MM: channel 58

  2. primary 40 MHz channel 54, primary 80 MHz channel 58

  3. primary 40 MHz channel 64, primary 80 MHz channel 60

  4. primary 40 MHz channel 60, primary 80 MHz channel 56

Answer: A

Question No: 14

A WLAN engineer has just completed a wireless network installation using Cisco 2700 series access points. After checking the WLC, it seems that the APs are running in medium power. What effect will this have in the APs?

  1. Due to insufficient power, the access points are not broadcasting any Wireless networks.

  2. Due to insufficient power, only the 2 4 GHz radio is up.

  3. Due to insufficient power the access points have dynamically shifted from 3×4 to 3×3.

  4. Due to insufficient power the access points have dynamically shifted from 4×4 to 3×3.

Answer: C

Question No: 15

An engineer is troubleshooting non-802 11 interference and observes this output. Which type of interference signatures can be identified?

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

  1. one frequency hopping Bluetooth

  2. two healthy CCK and one malformed OFDM

  3. three broadband jammers

  4. two strong microwave ovens and one moderate

Answer: B

Question No: 16

An engineer must open a support case with Cisco TAC. Which two commands verify the model and serial number of a controller? (Choose two)

  1. show sysinfo

  2. show udi

  3. show inventory

  4. show boot

  5. show tech-support

Answer: A,B

Question No: 17

A network engineer is troubleshooting why EAP authentication with a client is failing. Which two commands should be used to resolve the issue? (Choose two)

  1. debug dot1x notifications enable

  2. debug dot1x events enable

  3. debug arp

  4. debug aaa detail enable

  5. debug aaa events detail enable

Answer: B,E

Question No: 18

Refer to the exhibit.

A client reports being unable to log into the wireless network, which uses PEAPv2. Which two issues appear in the output? (Choose two)

Ensurepass 2018 PDF and VCE

  1. The AP has the incorrect RADIUS server address

  2. There is a problem with the client supplicant

  3. The AP has lost IP connectivity to the authentication server

  4. The authentic at ion server is misconfigured on the controller

  5. The EAP client timeout value should be increased

  6. The authentication server is misconfigured in the WLAN

Answer: A,C

Question No: 19

Clients are failing EAP authentication A debug shows that an EAP handshake started and the clients are then de-authenticated. Which two issues can cause this problem#39;? (Choose two.)

  1. The clients are configured for machine authentication, but the RADIUS server is configured for user authentication.

  2. The WLC has not been added to the RADIUS server as a client.

  3. The WLC certificate has changed.

  4. The shared secret of the WLC and RADIUS server do not match.

  5. The WLAN is not configured for the correct EAP supplicant type.

Answer: B,E

Question No: 20


The Big Engineering IT team has been working in the lab to do some testing of some new features the existing network won#39;t support. They are AP Croups, AP Failover, and Local

Web Auth. They have been having problems with all three features. In this test environment the controllers only support the Composite and Structural Engineering and Aerodynamic Engineering groups. All SSIDs should omit the department name. Refer to the exhibit. This is a diagram of the floor plan for the Big Engineering office and the distribution of the departments. The tables below show how the controllers have been configured.

Note, not all menu items, text boxes, or radio buttons are active.

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

When you review the configuration of the test network controller what needs to be changed to resolve the problems? (Choose four.)

  1. Change the High Availability Primary Controller Management Interface IP address.

  2. Remove the current WLANs and replace them with WLANs that have the same SSID names as on the AE-2504A controller.

  3. Add the Local Net User names and passwords

  4. Change the Layer 2 security to none and Layer 3 Security to Web Policy for the CSE- Contractors WLAN

  5. Remove me current WLAN from the CSE-WLAN AP Group and add all three of the WLANs configured in the CSE-2504A

  6. Add the CSE APs to the CSE-WLANs AP-Group.

Answer: B,C,D,F

100% Ensurepass Free Download!
300-370 PDF
100% Ensurepass Free Guaranteed!
300-370 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No