300-080 Latest Exam (May 2018)

[Free] 2018(May) Dumps4cert Braindumps Cisco 300-080 Dumps with VCE and PDF Download 31-40

May 28, 2018

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May Cisco Official New Released 300-080
100% Free Download! 100% Pass Guaranteed!

Troubleshooting Cisco IP Telephony amp; Video v1.0

Question No: 31

Where in Cisco TMS would you see if a system is registered to a Cisco VCS or a Cisco Unified Communications Manager?

  1. Systems gt; Registration

  2. Navigation gt; Systems gt; Registrations

  3. under Registration on the System Administration tab

  4. System Overview

  5. Settings gt; Provisioning

  6. where you start the Cisco Unified Communications Manager RTMT under Systems and Reports

Answer: D

Question No: 32

Refer to Exhibit:

Dumps4Cert 2018 PDF and VCE

After reviewing the trace in the exhibit, what was the Directory number of the called party?

A. 2001

B. 5010

C. 1905

D. 2003

Answer: D

Question No: 33

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

Assume a centralized Cisco Unified Communications Manager topology with the headquarters at RTP and remote located at the U.K. All route patterns are assigned a route list that contains a route group pointing to the local gateway. RTP route patterns use the RTP gateway, and U.K. route patterns use the U.K. gateway.

When a U.K. user logs into an RTP phone using the Cisco Extension Mobility feature and places an emergency call to 0000, which statement about the emergency call is true?

  1. The call will match the U.K_Emergency route pattern partition and will egress at the RTP gateway.

  2. The call will match the U.K_Emergency route pattern partition and will egress at the U.K. gateway.

  3. The call will match the RTP_Emergency route pattern partition and will egress at the RTP gateway.

  4. The call will match the RTP_Emergency route pattern partition and will egress at the

    U.K. gateway.

  5. The call will fail.

Answer: B

Question No: 34

After a Cisco Unified Communications Manager system is installed, users report problems when more than four users attempt to join a Meet-Me conference. Which parameter should you increase?

  1. Maximum Ad Hoc Conference, Call Manager Service Parameter

  2. Maximum Ad Hoc Conference, Enterprise Parameters Configuration

  3. Maximum Meet-Me Conference, Call Manager Service Parameter

  4. Maximum Meet-Me Conference, Enterprise Parameters Configuration

Answer: C

Question No: 35

An inbound call from the PSTN is not reaching the directory number that it is calling. When the PSTN phone calls the correct DID, only a dial tone is heard. Which command resolves this issue?

  1. (config-dial-peer)#direct-inward-dial

  2. (config-controller)# no provide-outside-dialtone

  3. (config-if)#no dial-tone

  4. (config-dial-peer)# no dial-tone

  5. (config-if)#direct-inward-dial

  6. (config) allow inbound dial-peer 1

Answer: A

Question No: 36 DRAG DROP

Drag the network-related video issue on the left to its root cause on the right.

Dumps4Cert 2018 PDF and VCE


Dumps4Cert 2018 PDF and VCE

Question No: 37

Refer to the exhibit.

Dumps4Cert 2018 PDF and VCE

A CUCM user has been configured to use the Mobility feature and is expecting their home phone 408-555-6016 to ring simultaneously when their office phone is called. What configuration change needs to be made to allow this happen?

  1. Select the Enable Move to Mobile check box.

  2. Select the Enable Extend and Connect check box.

  3. Select the Line Association check box.

  4. Deselect the Enable Single Number Reach check box.

Answer: C

Question No: 38

Which three statements about SAF forwarding are true? (Choose three.)

  1. It supports DNS and IP addresses.

  2. The SAF Forwarder configuration can be updated without connecting to Cisco Unified Communications Manager.

  3. It requires the SAF Forwarders to use the same configuration as the IOS switch.

  4. It is supported on IPv4 only.

  5. It is supported on IPv6 only.

  6. It requires a unique IP address for each SAF Forwarder.

Answer: A,B,F

Question No: 39

You enabled Cisco Unified Mobile Connect for a user, but the user is unable to send calls to a mobile phone from the desk phone. What do you do to resolve the issue?

  1. Restart the phone, and verify that the key is present.

  2. Under User Management gt; User, make sure that the Mobility option is selected.

  3. Make sure that the phone is subscribed to Extension Mobility.

  4. Add the mobility key to the softkey template that the phone is currently using.

Answer: D

Question No: 40

Refer to Exhibit:

Dumps4Cert 2018 PDF and VCE

What was the cause for the call termination?

  1. No route to called number

  2. Outbound gateway was not found

  3. Calling party abandoned the call

  4. Called party cancelled the call

  5. Call completed successfully

Answer: C

100% Dumps4cert Free Download!
Download Free Demo:300-080 Demo PDF
100% Dumps4cert Pass Guaranteed!
300-080 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No